拉力机新客户培训要领

Tensile machine new customer training

恒旭是一家负责任的企业。对于对于刚刚购买力拉力试验机的客户来说，要急于解决的问题是让操作人员尽快掌握它拉力试验的操作步骤、方法以及试验中需要注意的细节。如果不进行系统的培训，既浪费时间又有可能伤害到拉力机。因此，恒旭会派专业的技术人员对操作人员进行培训。只有这样我们才能在zui短的时间内把操作拉力试验机的技术*掌握，才能尽快的进行材料的拉力测试，让产品尽量更快的投入生产。下面恒旭小编就把培训的内容简单的介绍一下，希望对大家有所帮助。

Hengxu is a responsible enterprise. For customers purchasing power for just a tensile testing machine, the desire to solve problems is to allow operators to master it as soon as possible the operation steps and methods of the tensile test and trial need to pay attention to details. Without systematic training, it is a waste of time and can hurt the pull machine. Therefore, hengxu will send professional technicians to train operators. Only in this way can we fully grasp the technology of the operation tensile testing machine in the shortest time, so as to carry out the tensile test of materials as soon as possible, so that the product can be put into production as quickly as possible. Here is a brief introduction of the training. I hope I can help you

  一、拉力试验机的操作步骤

Ⅰ、 Operation procedure of tensile testing machine

1、如果想要完整的完成整个拉力试验，那么我们需要对拉力试验机的操作过程“了如指掌”，我们首先仔细阅读拉力机的使用说明书。当我们对拉力机了解之后就跟着技术人员一起进行拉力试验。

1. If we want to complete the whole tension test, we need to know the operation process of the tensile testing machine, and we will first read the instruction manual of the pull machine carefully. When we learned about the pull machine, we followed the technicians to carry out the tension test.

2、*步先打开电脑上的软件测控系统,再打开试验机电源。根据欲进行的试验选择相应的试验类型。

2. The first step is to open the software measurement and control system on the computer, and then turn on the test machine power. Select the test type according to the experiment.

3、然后选择适当的速度使试验机升降运行一下,确定各系统运行正常。

3. Then select the appropriate speed to lift the test machine up and down to make sure the system is operating normally.

4、依据要进行的试验的次数,新建出相应的试验记录条数；并填入相应的批号、编号、试验环境、试样尺寸等相关数据。

4. According to the number of trials to be conducted, the corresponding test record number shall be created. Fill in the corresponding batch number, number, test environment, sample size and other relevant data.

5、在拉力机夹具上夹紧要试验的材料。

5. Clamping the material of the critical test in the tension machine clamping device.

6、根据试验所需要的试验力和变形的范围,选择合适的试验力和变形的档位(量程)。

6. According to the test force and the range of deformation required by the test, select the appropriate test force and the deformation gear (range).

7、清零：将试验力、变形、位移清零。

7. Clear zero: the test force, deformation and displacement are zero.

8、准备工作完毕之后，点击开始按钮进行拉力试验。

8. After the preparation, click the start button to carry out the tension test.

9、待试验被拉断之后，保存得出的数据结果或者打印。

9. After the test is pulled off, save the data result or print.

10、关闭电源。

10. Turn off the power.

二、操作拉力试验机的时候要注意的细节

    1、实验前先检查拉力机工作台是否放置平稳。

    2、夹具必须将试验材料夹具，防止脱落。

    3、传感器的连接线路要定期的检测和保养。

4、试验机的轴承部位要定期的加润滑油。

Ⅱ、Attention to detail when operating tension testing machine

1. Check the bench of the pull machine before the experiment is stable.

2. The fixture must be clamping the test material to prevent shedding.

3. The connection line of the sensor should be tested and maintained regularly.

4. The bearing part of the test machine should be lubricated regularly

 三、要会对拉力试验机的故障进行排查和解决

    1、当拉力机出现问题的时候我们要对它进行故障分析，看看是哪里出现问题。

    2、在出现问题的地方可以维修也可以更换新的零件设备。

3、如果实在找不出故障的原因，应该立即咨询生产厂家，让技术人员帮我们解决。

Ⅲ、The failure of tensile testing machine should be checked and solved

1. When the tension machine is in trouble, we will analyze it and see where the problem occurs.

2. Can repair or replace the new parts equipment in the area where there are problems.

3. If there is no reason for the failure, we should call the manufacturer immediay and ask the technician to help us solve it.